Solid Green The brushrolls are on and working as they should.
Solid Red There is a jam in the brushroll area. Turn your vacuum off and remove the blockage.
No Light The brushrolls are off because the vacuum is off.

1. Press the Wand Release button on the top of the wand to disconnect the handheld vacuum from the wand. OR To remove the dust cup from the handheld vacuum, squeeze the two Dust Cup Release buttons on both sides of the base at the same time, then pull out the dust cup.
2. Hold dust cup over a trash bin and press the Empty button on the front of the dust cup. The bottom lid will open, allowing the debris to fall out.
3. Once dust cup is empty, close the bottom lid and insert dust cup back into handheld vacuum until you hear it click into place.

1. Insert the wand into the motorized floor nozzle connector, pressing it in until it clicks into place.
2. Insert the handheld vacuum into the top of the wand, pressing it in until it clicks into place.
3. Snap accessory storage clip onto the wand. Store one accessory on top holder and one accessory on bottom holder

1. Plug the unit in and recline the wand.
2. Slide the power switch to appropriate speed setting (I or II) and start cleaning.

Bare Floor, Area Rugs (I) – The brushroll and the Soft Roller both spin together slowly to clean bare floors and delicate area rugs. The Soft Roller traps fine dust and large particles, while the brushroll directs that debris to the suction channel. High Pile Carpets (II) – Both brushrolls spin faster, working together to pick up debris below the surface of your carpets.

Wand

1. Stand the vacuum upright. Step on the foot pedal and pull the wand up to disconnect it from the motorized floor nozzle.
2. Attach desired cleaning accessory.

Handheld

1. Press the Wand Release button on the top of the wand to disconnect it from the handheld vacuum.
2. Attach desired cleaning accessory.

1. Press the Wand Release button on the top of the wand to disconnect the handheld vacuum from the wand. OR To remove the dust cup from the handheld vacuum, squeeze the two Dust Cup Release buttons on both sides of the base at the same time, then pull out the dust cup.
2. Hold dust cup over a trash bin and press the Empty button on the front of the dust cup. The bottom lid will open, allowing the debris to fall out.
3. Once dust cup is empty, close the bottom lid and insert dust cup back into handheld vacuum until you hear it click into place.

1. Pre-Motor (foam and felt): Lift the latch on the top of the handheld vacuum to open the filter cover. Take out filters and tap loose dirt off them. If more cleaning is needed, rinse filters with water only and let them air-dry completely. To reinstall them, insert the felt filter first, place the foam filter on top of it, and close the filter cover.
2. Post-Motor: Access the Post-Motor filter under the handle. Remove and rinse the filter with water.

Pre-Motor Filter Kit (Foam & Felt) XPMFK320 Clean once a month. Post-Motor Filter XPSTFH380 Clean once a year.

1. Remove the wand from the handheld portion and check all dust cup intake openings.
2. Remove the floor nozzle from the wand and check the wand for blockages.
3. Tilt neck of floor nozzle back to straighten the airway. Remove blockages.

1. Press down on the two buttons on the floor nozzle to pop up the brushroll garage lid.
2. Lift the brushroll out by the tab on the left side. To remove any string, hair or debris that may be wrapped around the brushroll, use the onboard hair removal tool. The tool is located in a compartment on the nozzle, above the brushroll.
3. To reinstall the brushroll, return it to the brushroll garage. Press down on the brushroll garage lid until you hear it click into place.

 Charcoal

4.5lg

W 28 x D 23 x H 83 cm

 960W

 Carpets and hard-floors

Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinserting in the vacuum.
Dust cup may be full; empty dust cup.
Check floor nozzle for blockages; clear blockages if required.
​ Remove any string, carpet fibers, or hair that may be wrapped around the brushroll and Soft Roller or trapped behind the Soft Roller.

Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Turn off the unit to disengage the brushroll and restart with the Power slider switch.

If Brushroll Indicator Light on the floor nozzle turns red, the brushroll and/or Soft Roller have stopped spinning. Immediately turn off and unplug vacuum and remove blockage before reconnecting and turning vacuum back on.
If Brushroll Indicator Light on the floor nozzle is green, the blockage has been successfully cleared.